How To Use A Trolling Motor With A Trolling Motor Parts – Foot Pedal

Posted on 2012年01月31日 by admin

Trolling Motor Parts DG mount freshwater trolling motor
In addition to standard outboard motors, many boaters also install smaller trolling motors on their boats. Trolling motors are small motors that connect directly to the boat battery. Trolling Motor Parts are used to navigate short distances and are preferred by many fishermen because their small and quiet propellers do not disturb fish. MotorGuide is a company that manufactures trolling motors that use a foot pedal to control the boat. If the foot pedal becomes non-responsive it may need to be adjusted or repaired. The foot pedal comes with an electronic ID that also needs to be activated.
Forward movement
1 Sit on the seat closest to the boat’s bow, or whichever is closest to the trolling-motor foot control.
2 Choose the speed setting you wish to use on your trolling motor. All trolling motors are different but most have a numbered speed control on the foot controls ranging from 1 (slowest speed) to 5 or 10 (fastest speed).
3 Depress either the “Constant” or “Momentary” control switches on the foot controls, usually placed on the sides or ends. These can be depressed by simply pressing them in with the end of your shoe or toe. This action will cause the trolling motor to turn on and begin moving the boat. Some trolling motor models only have a “Constant” or “On” button. “Constant” will run the Transom Mount Trolling Motor continuously until you turn it off again, and “Momentary” will run the motor for a short time.
Left and Right Movement
1 Depress the front of the foot control or “toe down” to turn right.
2 Press the rear of the foot control down or “heel down” to turn left. This occasionally varies by manufacturer, but this configuration is generally the same on nearly all foot-controlled trolling motors.
3 Release the foot control to begin going straight again. To continue going in a straight line simply do nothing and the trolling motor will go straight by default.
The article comes from Trolling Motors.

Posted in Accessories, trolling motor | Comments Off

Install A 24 Volt Trolling Motor

Posted on 2012年01月11日 by admin

saltwater transom mount trolling motor(finite variable speed)
A bow mount Pinpoint Trolling Motor gives a fisherman the most control over his boat while fishing. It pulls the boat through the water and gives better control and maneuverability than one designed to mount on the transom. Any boat 14 feet or longer can accommodate a bow mount, though you may have to modify the bow if it doesn’t have a front deck. You’ll need a front deck large enough to secure the mounting base to it and to allow enough room to stow the entire shaft and motor head on the deck without hanging out over the bow.
1 Install the mounting bracket to the trolling motor from 24 Volt Trolling Motor Wiring Diagram in accordance to the manufacturer’s instructions, if one is needed. This may require wrenches to tighten the mounting bolts.
2 Loosen the mounting brackets on the trolling motor by rotating the adjustment screws counterclockwise. Make sure that the mounting bracket clamps are open wide enough to fit over the edge at the top of the bow.
3 Place the trolling motor on the bow of the jon boat. Slide the trolling motor to the desired location on the bow.
4 Turn the adjustment screws on the mounting bracket clockwise to secure the trolling motor to the bow. Tighten until the trolling motor is securely attached to the bow.
The article comes from Trolling Motors.

Posted in electric trolling motors | Comments Off

Move A Houseboat Thruster Trolling Motor

Posted on 2012年01月5日 by admin

Electric Thruster Stern Thruster DR mount freshwater trolling motor
When out on the lake or open waters with your yacht, weather conditions can change in an instant. As you approach the harbor, you may find the current and wind have overtaken the bow. This makes for a stressful situation for even the best operators and skippers. However, a Electric Thruster can help alleviate this stress. The bow thruster is a power device installed in the boat’s hull that gives the boat more maneuverability and steering precision. You can regain control of your boat in inclement weather by installing a bow thruster.
1 Turn on your bilge blower motor while you are still tied to the dock, and let the blower run for several minutes. This purges all gas vapors from the engine compartment, if equipped with an inboard or stern drive motor. Turn the engine on and let it reach normal operating temperature. Make note if you have a water current or surface wind pushing you into the dock. Make note also as to whether your bow is facing land or toward the open water.
2 Turn on the thruster generator, if your houseboat is equipped with hydraulic thrusters, and let it warm up. If the thrusters are electronically controlled, turn on the power source. If your boat is facing open water from the dock position, and if you have a crosscurrent or breeze holding you against the dock, activate the port bow thruster to pull the starboard side of the bow away from the dock. The thruster control lever may be a toggle switch, which you can hold to the right, or it may be a turn-knob, which you can turn to the right. Consult your owner’s manual for specific details.
3 Have an assistant cast off the lines. Let the bow swing to starboard, 5 to 10 feet away from the dock, then activate the throttle, to motor out into the channel or open water. If you have a Stern Thruster only, with the bow facing inland, activate the starboard stern thruster and let the stern pull away a safe distance from the dock, then throttle the houseboat motor in reverse. This will gain you enough clearance to make a 180-degree turn into open water.
4 Activate the stern and bow thruster simultaneously when launching, if equipped with dual thrusters. Let the houseboat “crab” sideways and outward from both ends of the dock, then throttle the motor forward or in reverse, depending upon your craft’s direction in relation to the dock. This will work in a crosscurrent wind condition or in calm water.
5 Approach the dock slowlyh, with just enough rudder control and speed to overcome a crosscurrent or wind condition. Angle the bow into the dock, and have an assistant tie off the bowline on a dock cleat, while you active the port stern thruster to abut the stern into the dock. Tie off the stern line. Activate the starboard stern thruster if you are approaching the other side of the dock.
6 Activate the stern and bow thrusters simultaneously when approaching the dock against a crosscurrent or crosswind. Make your approach straight in, parallel with the dock, then bring the engine to idle and then active the both thrusters. Remember that when facing the dock, you will activate the stern and bow thrusters furthest from the dock, using the same speed on both, or reducing the speed to one thruster if the bow or stern begins to drift outward. This maneuver is called “walking” into the dock.
7 Drive straight toward land if you intend to beach and anchor your houseboat. Depending upon the direction of the current and wind, use the stern thruster to keep your boat perpendicular to the shore as you approach. If your stern begins to swing right, activate the right, or starboard thruster, to straighten it out. When you beach and shut your motor off, keep a stern thruster activated to maintain a perpendicular profile until you are staked and anchored to the shoreline.
8 Approach close to the edge and stern first to the dock in reverse for a backing-in maneuver. Make sure you have the houseboat parallel with the lock. Turn the helm to the left to swing the stern into the dock, while activating the starboard bow thruster. This procedure resembles a parallel park maneuver. Reverse the helm direction and activate the port bow Trolling Motors to reach the other side of the dock.

Posted in electric trolling motors, Thruster, trolling motor | Comments Off

Install An Transom Mount Trolling Motor On A Kayak

Posted on 2011年12月28日 by admin

Kayak Trolling Motor
If you own a pedal Kayak as a “lake toy,” you know that, on occasion, you can get tired of a pedaling. You might wish for a Kayak Trolling Motor to take you back to shore at a leisurely pace, quietly. You might even want to be able to take your pedal Kayak out on the lake when you’re too tired to pedal out. The solution to your problem may be a motor mount for an electric trolling motor, specifically designed to fit onto the hull of a pedal Kayak.
Mounting Bracket
1 Determine the dead center of the back of your kayak. It’s important that the motor is fitted in a central position to ensure that the steering mechanism will work correctly when the motor is on and the kayak is in motion.
2 Lower the mounting bracket over the back of the boat with the motor shaft angled out of the water.
3 Screw the mounting bracket into place, taking care not to over-tighten.
4 Hold the Transom Mount Trolling Motor shaft with one hand and loosen the depth adjustment screw. Alter the length of the motor shaft to the desired length, taking into consideration the depth of the water you’re planning to travel on. Make sure that the propeller is not positioned too low because it will be damaged if it comes into contact with the bottom of the river or the riverbank.
Mounting Ball
1 Identify a flat surface at the back of your kayak where you’ll be able to fix the mounting ball. This should be at the center of the vessel unless it has a rudder, in which case it should be slightly to the side.
2 Loosen the clamps around the motor boom shaft and lengthen so that the propeller shaft will clear the back of the kayak when secured in place. Tighten the screws when complete.
3 Fix the mounting ball to the flat surface at the back of your kayak so that the motor is placed at the center of the vessel. Drill holes in the back of the kayak and secure it in place. If the motor shaft boom is not horizontal, support it with a rubber rest to correct its level.
The article comes from Trolling Motors.

Posted in electric trolling motors | Comments Off

Maintain A Shakespeare Trolling Motor

Posted on 2011年12月20日 by admin

Shakespeare Trolling Motor DR mount saltwater trolling motor
MotorGuide trolling motors are also called Stern Thruster, allow freshwater anglers to sneak up on fish and also to position the boat for easy casting. Trolling motors are powered by electricity, so they are quieter and more reliable than outboard motors. However, they do sometimes have problems. Damaged propellers, weak batteries and blown fuses can put a stop to your day on the water.
1 Check the battery lead cable and connections before using the motor. Make sure that the connectors are tight, and that there are no kinks or frays in the cables. Check that the propeller nut is tight, and the blades have no damage.
2 Remove a damaged propeller by unscrewing the propeller nut using a prop wrench. Disconnect the Mercury Thruster from the battery, then hold the prop in one hand while unscrewing the nut with the other.
3 Replace the propeller with a new prop, making sure it fits securely over the pin in the propeller shaft. Screw the propeller nut back in with the wrench.
4 Remove any weeds, fishing line or other debris after using the motor. Check the propeller nut again, and rinse the motor with fresh water to remove any dirt.
5 Lubricate any pivot points on the motor with non-aerosol, non-solvent-based lubricant.
The article comes from Electric Motor.HAIBO Trolling Motors – Electric Trolling Motors specialized in manufacturing, High quality products of Electric Motor, China Trolling Motors Manufacturers

Posted in Thruster, trolling motor | Comments Off

How to Choose Your Safe Trolling Motor

Posted on 2011年12月13日 by admin

Trolling Motor Wiring wire control
An electric trolling motor is a key piece of gear for any boat. While the electric trolling motor can definitely be used for trolling, their primary purpose is to place your boat or working structure.The article comes from Trolling Motor Accessories.
Choosing a trolling motor is not at all difficult if you do your homework before you head to the store to buy one. There are several factors to be considered in the selection of a trolling motor, and it is possible to deal with each question without ever leaving home. These factors run the gamut from the boat size, economic questions and on to the type of water you will be operating in.
1 Determine the type of trolling motor you will need. Is the boat a small, open boat, such as a row boat, or a large boat, such as a bass fishing boat? Is the boat lightweight? These factors will help you know if you need a bow or transom-mount motor and its approximate thrust. Measure the boat to determine length and depth.
2 Know your price range. There’s no sense in looking at autopilot trolling motors with a built-in transducer if your budget is less than $500.
3 Consider where you’ll be fishing. A calm, secluded lake will require a trolling motor with much less thrust than will a lake known for the windy conditions or a raging river. Overpowering wastes money, under-powering can render a trolling motor nearly useless.
4 Determine how much battery space and carrying capacity your boat has. Batteries are heavy and take up a lot of space. Knowing how many batteries you can carry to power your trolling motor will help refine your search. You likely won’t want a 36-volt trolling motor in a 16-foot fishing boat, for example.
5 Make a chart of your desired features and compare that to the manufacturer’s specifications.
Size:There are a few features to think about when you determine to purchase electric Trolling Motor Wiring. This is a buy where larger is often better as an undersized motor will leave you floundering, so take the build of you boat into account. Aluminum boats are noticeably lighter than their fiberglass counterparts. For example, a fiberglass boat is heavier than an aluminum boat and will want a bigger motor.
Shaft Length:The shaft length of your motor is another critical feature. If you have a bow mounted motor and the shaft length is too short, your propel with be at the mercy of the waves the moment you encounter a stiff wind, constantly in and out of the water. Not only is this bad for your trolling motor as it is supposed to operate in water, but a prop that won?t stay in the water can cause you to lose control of your boat.
Power:When achievable, you should always choose a 24 volt electric trolling motor over a 12 volt model. The 24 volt model has two deep cycle batteries while the 12 volt model has only one deep cycle battery. The 2 deep cycle batteries sported by the 24 volt electric Trolling Motors allow it to last two times as long as the 12 volt model. Just ask yourself, do you actually want to risk running out of your electric power halfway through the day? And what if it?s through a fishing tournament?

Posted in Accessories, electric trolling motors, Saltwater | Comments Off

Trolling Motors Thrust You Need And Their Advantages

Posted on 2011年12月8日 by admin

 

Trolling or angling is a fishing method that uses baited fishing lines. These fishing lines are drawn through the water while being attached to the rear part of a moving boat. To keep this boat moving, some sort of a special motor must be used. It should be the one that creates little noise so as not to disturb the fishes and spoil the whole fishing experience. This is where the Trolling Motors comes in.
What information do you need for basing your decisions in choosing the proper thrust for a trolling motor? Especially if you have never owned a trolling motor of your own! The best decisions can be based on information obtained, from asking people you know that own trolling motors. You should consider three factors: boat weight, length, and your typical fishing conditions, with boat weight being the most important factor.
Determined by boat weight- A simple rule is use a trolling motor with two pounds of thrust for every 100 pounds of boat weight. This measurement factor is based on a boat loaded to capacity. You can usually find the weight of your boat and the maximum person, motor and gear weight in an owner’s manual, on the manufacturer’s website or it is sometimes posted right on a sticker at the boat controls. A 1270 pound boat with 1100 pound capacity is 2370lbs/100 X 2lbs/100 yields a minimum thrust of 47.4lbs. Based on weight alone you would look for at least a 50lb thrust trolling Electric Motor.
Determined by boat length- The second most important factor to consider is boat length. Our chart below will give you a good starting point for the thrust range you should be considering given your boat length. This information, if unknown, can also be obtained from an owner’s manual or from a manufacturer website.
Boat Length (ft) Minimum Thrust (lbs) Max Weight (lbs) Minimum Thrust (lbs)
12′-14′ 35 1500 30
15′-16′ 40 2000 40
17′ 50 2500 50
18′ 55 3000 60
19′ 65 3500 70
20′ 75 4000 80
21′ 80 4500 90
22′+ 80-101 5000 100
If your boat happens to fall into two different thrust categories based on these charts, we’d suggest using the minimum thrust figure recommended via the weight method, since it is the number one consideration.
There are a lot of reasons why the trolling motors are good. In addition to the fact that it avoids creating a disturbance while fishing, it virtually meets almost any fishing application and personal tastes and preferences. Each trolling motor also comes with built in features that suits either freshwater or saltwater fishing, depending on the consumer’s preferences. There are also other motors that boast their indestructible composite shaft which is guaranteed not to corrode, rust, or just degrade. Indestructible indeed!
In addition to this, there are companies that also provide a wide range of choices for parts and accessories of every purchased motor. This means that the convenience brought about by the trolling motor itself could still be improved. Now what’s going to be better than that?
Posted in electric trolling motors, trolling motor | Tagged , , | Comments Off

The Way Boat Electric Thruster Work

Posted on 2011年11月28日 by admin

Boat Electric Thruster
It happens to be a fact that the sport most people participate in, is fishing. The reason for this could simply be a desire to go somewhere, far away from cities with the associated pollution, squalor, high rise buildings, fast pace and high population. In other words, the peace and quiet that can be found along the banks of a quiet river in the outdoors.
Fishing has long been an activity in which man has taken part. This would be because he needed to find food and fish is a top quality source of food. Whether man was aware of the high nutritional value of fish in those days seems not to be a point of discussion. Records show, though, that one of the earliest methods of using a hook was a piece of wood sharpened at both ends and tied to a line. This caught in the mouth of the fish in a way similar to the hook and line one encounters now.
Electric Thruster Overview
Electric Thrusters are electric motors that fishermen and others use when they want to move their boat around the water but make a minimum of noise while doing it. Electric Thrusters also allow users to operate them at slower speeds than they could with a standard fuel motor. This type of motor comes in a variety of shaft sizes, so Electric Thrusters can be used on small and large boats.
The Power Source
Twelve-volt marine batteries provide the power that is needed to operate Electric Thrusters. They are wired with a set of positive and negative wires. These wires are connected to the corresponding positive and negative terminals on the marine battery. Once connected, Electric Thrusters draw their power from the batteries and will run until the batteries run out of charge, at which time they can be re-charged. Electric Thrusters are quieter than fuel-burning motors because they run off of electricity. The amount of power Electric Thrusters have is called thrust, and the higher the thrust, the faster they go.
Using Boat Thruster
In most instances, Boat Thrusters are mounted on the bow or stern of a boat of other watercraft. They can be placed there permanently or mounted on brackets that allow users to quickly take them on and off. Some Boat Thrusters have handles on them that users manipulate with their hands to turn the motor left or right, frontward or backward. Other Boat Thrusters have special foot controls. Some of these devices are plugged into the Boat Thruster and others are wireless, but both varieties allow users to steer the motor using only their feet. By applying pressure to the left side of the foot control, for example, users can make the Boat Thruster itself turn to the left.
On the Water
When the Boat Thruster is under power, a prop at the bottom of the motor spins through the water. This is how Boat Thrusters propel boats and other watercraft. Whether Boat Thrusters have a handle or a foot control, users can decide how much power to send to the prop. The more power, the faster the prop spins and the faster the boat or watercraft moves. Other factors that influence the speed of Boat Thrusters are the length and number of blades on the prop, as well as weather conditions like wind and water conditions like waves. No matter what the conditions, though, the more water the prop pushes, the faster the boat moves.
Boat Thrusters are powered by marine batteries of either 12v, 24v or 36v. Choosing which motor you buy depends on how fast you need the boat to go. The length of the shaft also varies as it depends on the depth of the water to be fished and what your fishing preferences are. For instance, if you were a keen tournament participant, you would probably be looking at one of the more powerful Boat Thruster.

Posted in Accessories, electric trolling motors, Freshwater, freshwater bow mount trolling motor, Saltwater, Thruster, trolling motor | Comments Off

Boat fishing equipment Electric Trolling Motors

Posted on 2011年08月29日 by admin

Boat fishing equipment,Electric Trolling Motors, in addition to a variety of specifications hook, line, swivels, connectors, scales, bait cage, large lead mound, a strong rubber band, luminous rods, floats and other structures and thus tied themselves into a variety of boat fishing fishing group (Shi-hung). These groups are generally fishing for fish of different varieties and sizes of fish with the design, the foreign component of the catch is very fine, almost because of the fish varies; but the general principle is the hook, fishing line and pull strength , varieties of fish to catch with the size, weight approximately match. As the fishing boat fishing group (official link), anglers should be according to their own situation, choose the appropriate form of fishing fishing group.

Boat fishing rod of choice, usually by small vessels to catch fish shallow coastal waters, fishing rod can ordinary Angeles; such as specialized fishing boat fishing by deep-sea fish, the use of professional boat fishing rod. Professional boat fishing rod and generally following the two, patch-based or nut-type, a rod tip a tip or two (hard-soft tone tune), there is fishing line through the pole outside the wire ring, but also through the rod inside of the tube “in-pass “The. Boat rod inserted after the two-phase length, 1.8 meters, 2.1 meters, 2.4 meters, 2.7 meters. According to different load from the boat pole, are marked on the rod body 120, 180, 300, 350, 400, 500, 600, 700 and so forth. For example, boat rod 120, can deal with 10 kg – 15 kg level in fish; 400 boat rod, you can challenge 40 kg to 50 kg-class of fish; 600 – 700 boat rod, enough to overcome the 100 kg class more “monster.”24 Volt Trolling Motor Wiring Diagram

Boat fishing pole holder-specific branch, are all resistant to seawater corrosion of stainless steel material, the lower fixed with screws tighten on the guardrail on the side of the ship, the upper pole and the card is good Tam board shake-line wheels, and with clamp screw After the boat pole cap clamping handle, the wire loop and roll round in the top of the pole and into a straight line on the rod tip is generally in the 45-degree angle Yang, Tam Kon fork up and down through the regulation to complete.

Boat fishing Fishfinder machine to screen size, divided into 6-inch, 8 inch, 10 inch. The first big feature is the aircraft navigation, it shows the coastline, track, channel, course, speed, range, estimated time of arrival, destination latitude and longitude, the satellite automatically locate, mark and other mobile tour drift. Control fish machine frequency 50 kHz, 120 kHz, 200 kHz, power 600 watts to 120 watts. Control test range, the minimum 8 meters, up to 1000 meters, full-color, with a clear reflection of submarine fixed zoom, automatic selection follow, submarine topography, geological features, depth, fish hearing alarms, fish, fish and night flashing lighting other functions, waterproof power, weight 1.5 kg. Reels, also known as reel, a human hand type electric manual dual-use, with the appearance of anti-sea erosion coating, there is more than a bearing, through manipulation, automatically closing line, pay-off, the value of fishing power 25 kg, 50 kg, 85 kg … … can be adjusted, and the closing line of the number of meters, the number of pay-meters, the number indicated on the screen can display. Manual winder, manual electric reel, fish, explore it with the same machines are high-tech products, when used, must be accompanied by 6-volt to 12 volt storage battery, simple, powerful, about 10 buses, generally build 1500 to 2000 meters.

Large hooks, which is the boat to catch big fish dragged the fish on board the necessary tools. In addition to the outside of a few large, anglers can also carry a small number of rock fishing tackle, for example, sometimes use small fish as bait, you have to take at any time fishing, so bring along some spare fishing tackle to bait, etc., so that “being prepared” .Mini Kota Trolling Motor

Posted in Uncategorized | Comments Off

Trolling Motor Accessories,YOU will enjoy them

Posted on 2011年08月16日 by admin

A few Trolling Motors are created specifically with regard to trolling, a fishing method which makes use of fishing rods as well as baits which are attracted across water. These types of motors allow fishing boats to make minimal possible sound in order to not really scare aside the actual seafood and to produce very little disturbance as you possibly can.
Such as everything else, trolling motors possess specific parts. A few are really essential to keep the motor up and running, others are additional for convenience. For requirement and convenience, you should buy all of the parts and accessories, although it is not compulsory. However, if you would like your own trolling Trolling Motor to function the best it could, buy all of the parts and accessories. The following are some of the  NINGBO BEILUN HAIBO MACHINERY CO.,LTD. Trolling Engine components.
3.5″prop with three blades
the prop is for Haibo Trolling Motor of 3.5″ O.D.(44lb-65lb) ,It is specially designed for improving the work efficiency,part no.is HP6.393.001.00
multi-functional bracket
For different versions of Haibo brand electronic Trolling Motor,either hand control or foot control.It can be perpendicularly 90 degrees tilted,further more, 360 degrees rotated in level direction.
Part no.is HP6.152.013.00.
foot switch
Foot control unit for DG mount and DR mount electronic motors.
Part no.is HP6.041.000.00.
trolling motor fuse
It can prevent electronic Trolling Motor from damage due to over-load current.
40amp HP7.710.003.00 50amp HP7.710.001.00 60amp HP7.710.002.00
remote control
For remote control funtion of Haibo electronic Trolling Motor.
Part no.:HP6.789.001.00
If you are intersted in others,please enter the following links: Freshwater , Saltwater , Accessories , New products and so all!

Posted in electric trolling motors | Comments Off